6201537
Description
2. Main Features
Model: 6201537
Type: Inductive proximity sensor
Detection target: All metal materials
Rated voltage: 10–30 V DC
Output type: 3-wire DC
Max load current: ≤ 200 mA
Protection grade: IP67 dustproof & waterproof
Working temperature: -25 °C ~ +70 °C
Built-in reverse polarity, overvoltage and short-circuit protection
Vibration resistant, shockproof, long service life
3. Safety Precautions
Disconnect power before installation and wiring.
Do not apply voltage beyond 10–30 V DC.
Reverse power connection is strictly prohibited to prevent sensor damage.
Keep away from high-power motors, transformers and strong magnetic interference sources.
Do not disassemble or modify the sensor arbitrarily.
Avoid mechanical impact, oil contamination and long-term damp working conditions.
4. Installation Guide
Fix the sensor with locking nut or mounting bracket.
Maintain rated effective sensing distance from metal target.
Install perpendicular to the detected surface for best detection accuracy.
Do not place extra metal parts around the sensing head.
Route the cable properly, avoid sharp bending and forced pulling.
5. Wiring Definition
Brown : DC +10～30 V Power
Blue : DC 0 V Ground
Black : Signal output
Shield: Ground only at controller side
6. Operating Instructions
Wire connection must follow the standard definition.
Power on, the sensor enters standby mode.
When metal enters effective detection range, indicator lights up and output acts.
When metal leaves the detection area, output resets and indicator turns off.
Suitable for direct connection to PLC, relay and automation controller input.
7. Troubleshooting
No indicator light: Check power supply and wiring integrity.
Always output ON: Metal target too close or surrounding metal interference.
Signal unstable flickering: Loose wiring, equipment vibration or power fluctuation.
Indicator on but no output: Signal wire broken or load faulty.
8. Maintenance
Clean dust and iron debris on the sensing surface regularly.
Check mounting tightness and cable wear periodically.
Avoid long-term operation in high temperature and corrosive gas environment.
Replace immediately if shell crack or cable aging occurs.
2. Main Features
Model: 6201537
Type: Inductive proximity sensor
Detection target: All metal materials
Rated voltage: 10–30 V DC
Output type: 3-wire DC
Max load current: ≤ 200 mA
Protection grade: IP67 dustproof & waterproof
Working temperature: -25 °C ~ +70 °C
Built-in reverse polarity, overvoltage and short-circuit protection
Vibration resistant, shockproof, long service life
3. Safety Precautions
Disconnect power before installation and wiring.
Do not apply voltage beyond 10–30 V DC.
Reverse power connection is strictly prohibited to prevent sensor damage.
Keep away from high-power motors, transformers and strong magnetic interference sources.
Do not disassemble or modify the sensor arbitrarily.
Avoid mechanical impact, oil contamination and long-term damp working conditions.
4. Installation Guide
Fix the sensor with locking nut or mounting bracket.
Maintain rated effective sensing distance from metal target.
Install perpendicular to the detected surface for best detection accuracy.
Do not place extra metal parts around the sensing head.
Route the cable properly, avoid sharp bending and forced pulling.
5. Wiring Definition
Brown : DC +10～30 V Power
Blue : DC 0 V Ground
Black : Signal output
Shield: Ground only at controller side
6. Operating Instructions
Wire connection must follow the standard definition.
Power on, the sensor enters standby mode.
When metal enters effective detection range, indicator lights up and output acts.
When metal leaves the detection area, output resets and indicator turns off.
Suitable for direct connection to PLC, relay and automation controller input.
7. Troubleshooting
No indicator light: Check power supply and wiring integrity.
Always output ON: Metal target too close or surrounding metal interference.
Signal unstable flickering: Loose wiring, equipment vibration or power fluctuation.
Indicator on but no output: Signal wire broken or load faulty.
8. Maintenance
Clean dust and iron debris on the sensing surface regularly.
Check mounting tightness and cable wear periodically.
Avoid long-term operation in high temperature and corrosive gas environment.
Replace immediately if shell crack or cable aging occurs.
Get a Quote